DROP OVER
PROTECTORS
ASSEMBLY:
• Inspect areas for safety hazards
• Place protector over cables
• Assemble sections by aligning female connectors over male connectors
• Press with foot to secure female connectors to male connectors
• Test installation for intended use
• Periodically inspect installation
NOTE:
Optional Anti-Slip Rubber Pads and Carpet Kit
with VELCRO
®
Brand Fasteners can be
purchased and easily installed on FastLane
Cable Protectors (see instructions below).
CHANNEL CAPACITY:
LOAD CAPACITY:
The Cable/Hose Protection System has different
load supporting capabilities depending on type of vehicle and temperature.
Suitability must be verified by testing under actual conditions.
OPERATING TEMPERATURE:
-40˚F to 120˚F (-40˚C to 48˚C)
CHEMICAL RESISTANCE:
Tested for compatibility with common
motor oils, gasoline and diesel fuel. Limited resistance to brake fluids and
other chemicals.
MATERIAL:
UV-stabilized polyurethane elastomer
CABLE/HOSE MANAGEMENT COMPONENTS
ASSEMBLY INSTRUCTIONS
#ZIS-FL
Ver: 2/11
Simply interlock with
L-connectors to extend
protection length.
®
DROP OVER CABLE PROTECTORS
CHANNEL CAPACITY - MAX. DIAMETER INCHES (mm)
FL1X1.5
FL1X4
1.5 in. (39 mm) width x .5 in. (12.7 mm) height
4 in. (101.6 mm) width x 1 in. (25.4 mm) height
FL2X1.75
1.75 in. (44.5 mm) width x 1 in. (25.4 mm) height
Drop over protectors do not prevent
abrasion to cable from below.
WARNING!
TWO CHANNEL OPTION
ONE CHANNEL OPTION
Before installing, ensure circular recessed
areas are free from dirt and debris. Apply
2-3 drops of Checkers Super Glue to the
top of the center post and then place a bead
of glue around the outer edge of the half
moon area. Align rubber pad slot with rib
on Cable Protector, then quickly place
Rubber Pad over the post and slot on cable
protector. Firmly push down with thumb
around the outer edge of Rubber Pad until
fully seated. Repeat until complete.*
RUBBER PAD INSTALLATION
1) Before installing, clean bottom edges of cable protector with a
dry rag. 2) Apply a generous bead of Checkers’ Super Glue to the
bottom edge of the cable protector (parallel with outer edge). 3)
Quickly place one end of the VELCRO® brand fastener over the
bead of glue, lay the VELCRO® brand fastener
strip down, and apply
pressure. 4) Repeat this
step for other side of
cable protector. Trim
excess strip with a razor
blade.*
CARPET KIT INSTALLATION
* For your safety, please wear safety glasses and rubber gloves.
Checkers Super Glue is best when stored refrigerated.
123
OPTIONAL TRACTION KITS
CPRPKIT.75-18 Optional Anti-Slip Rubber Pad Kit (includes 18 rubber pads) for FL1X1.5
CPRPKIT1-8 Optional Anti-Slip Rubber Pad Kit (includes 8 rubber pads) for FL1X4 or FL2X1.75
CPGLUE
1/2 oz Bottle of Checkers’ Clear Super Glue (best if kept refrigerated)
Use for Permanent Application of Anti-Slip Rubber Pads
CPCARPETKIT-3
Optional Carpet Kit with VELCRO
®
Brand Fasteners for All FastLane Models - Includes two
37" x .25" Black VELCRO® brand fastener strips and a 1/2 oz Bottle of Checkers’ Clear Super Glue (CPGLUE)
(1 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals